PMC6-2
Active 3-way nearfield/midfield studio monitor with two 6-inch bass drivers, a 2-inch soft-dome mid-range and a 1-inch soft-dome tweeter, each driven by its own 400W Class-D amplifier. Aimed at control rooms and immersive setups, with an upgrade path to a full-range system by adding a subwoofer.
- Active 3-way monitor with ATL bass loading
- Two 6" bass drivers, 2" soft-dome mid, 1" soft-dome tweeter
- 400W Class-D amp per driver: 4 channels in total
- Analogue and AES3 digital XLR input, AES3 through output
- SoundAlign network control via RJ45
- Adds PMC8-2 SUB for XBD mode down to 25Hz
Ritratti
8Reklami
Għad m’hemmx reklami ta’ dan il-mudell
Meta xi ħadd ibigħ PMC6-2, ir-reklami u l-istorja tal-bejgħ jidhru hawn.
Biegħ wieħed bħal danDeskrizzjoni
The 6-2 is a powered three-way monitor using ATL bass loading with a 2m effective line length. Two 150mm bass drivers, a 55mm soft-dome mid-range with a waveguide and a 27mm soft-dome tweeter are driven by four 400W Class-D amplifier channels. A DSP crossover provides driver protection, EQ, delay and polarity options. Frequency response is 33Hz to 25kHz (-3dB), with a maximum continuous SPL of 109dB at 1m.
Settings are made with the rear-panel controls or through the browser-based SoundAlign web interface, which can adjust a single monitor or a group. Available processing includes level trim, a high-pass filter, delay up to 30ms, low and high shelving filters, a 5-band parametric EQ and three user presets plus factory defaults. Hexagonal vent ducts reflect the Laminair airflow design. A ceiling-mount yoke allows suspension in multichannel or immersive systems.
A single XLR input switches between analogue and AES3 digital, and an XLR digital through output and an RJ45 network port are provided. An expansion card slot is reserved for future connectivity. Adding a PMC8-2 SUB and selecting XBD mode turns the pair into a twin-cabinet system extending low frequencies down to 25Hz.
Vidjo
Speċifikazzjonijiet
- Marka
- PMC
- Mudell
- PMC6-2
- Kategorija
- Studio › Monitors tal-istudio
Type and drivers
- Type
- Active 3-way nearfield reference monitor with ATL bass loading
- LF drivers
- 2 x PMC 150mm (6") studio 6 drivers
- MF driver
- PMC 55mm (2") soft dome mid-range
- HF driver
- PMC 27mm (1") soft dome tweeter
- Effective ATL length
- 2m (6.6ft)
Audio
- Frequency response
- 33Hz - 25kHz (-3dB) (@1m full space, on-axis)
- Sensitivity
- +4dBu input signal = 98dB SPL @ 1m
- Max continuous SPL
- 109dB @1m
- Max peak SPL
- 121dB @1m
- Directivity
- H +/-50 degrees, V +60/-40 degrees (-6dB off axis @10kHz)
- Latency
- 2.4mS
Inputs
- Input connector
- XLR switchable between analogue & digital AES3
- Analogue max input level
- +20/+24dBu (selectable)
- Analogue input impedance
- 22K ohm
- Digital input
- 16/24-bit AES3 signal, left, right or left + right
- Digital sample rate
- 18 - 192kHz
- Digital input impedance
- 110 ohm
Outputs
- Digital output
- XLR digital AES3 (fixed 24-bit @ 96kHz)
Connectivity
- Network
- RJ45 for use with PMC SoundAlign web interface
- Expansion
- Expansion card slot for future connectivity upgrades
Processing
- Level trim
- +/-10dB
- High-pass filter
- 20 - 200Hz, 12dB/Oct
- Delay
- 0 - 30mS
- Shelving filters
- LF & HF, 20Hz - 20kHz, +/- 10dB, Q 0.707
- Parametric EQ
- 5 bands, 20Hz - 20kHz, +/- 10dB
- User presets
- 3 + factory defaults
Power
- Amplifier power
- LF 2 x 400Wrms, MF 1 x 400Wrms, HF 1 x 400Wrms
- Mains
- 100 - 240VAC auto-switching, 50-60Hz (IEC C14)
- Power consumption (idle)
- 50W
- Power consumption (max)
- 1500W
Physical
- Dimensions (H x W x D)
- 400mm (15.7") x 430mm (16.9") x 372mm (14.6")
- Weight
- 21.3kg (47lbs) each