ISA ADN2
Optional two-channel analogue-to-digital card for the ISA One mic preamp and DI. It adds Dante, AES3, ADAT and S/PDIF digital outputs at up to 24-bit/192kHz, for studios that want to put the ISA preamp on a network or into a digital rig.
- Two-channel A-D card for the ISA One preamp and DI
- Sample rates up to 24-bit/192kHz
- Dante over primary and secondary RJ45 ports with auto switchover
- AES3 on XLR, ADAT on TOSLINK, S/PDIF on RCA
- BNC Word Clock input and output, switchable termination on input
- RedNet Control and Dante Controller software included
Fotky
6Inzeráty
Tento model zatiaľ nemá inzeráty
Keď niekto bude predávať ISA ADN2, inzeráty a história predajov sa zobrazia tu.
Predať taký istýPopis
The ISA ADN2 is an add-on A-D conversion card for the ISA One. It converts the preamp's two channels to digital at sample rates from 44.1kHz up to 192kHz at 24-bit, so the ISA One can feed a Dante network or conventional digital inputs directly.
Outputs include primary and secondary RJ45 Dante ports, which provide redundancy with automatic switchover if one link fails. Alongside Dante there is an XLR AES3 output, a TOSLINK ADAT output and an RCA S/PDIF output. BNC Word Clock input and output connectors let the card sync to external clocks, sync the Dante network to a house clock, or clock other equipment from the Dante network.
Once on Dante, the ISA One can talk to Focusrite RedNet devices, Red interfaces and Dante-enabled products from other makers. Metering and settings are handled in RedNet Control, and routing is set up in Dante Controller, with no hardware patching needed. Both software tools are included.
Video
Parametre
- Značka
- Focusrite
- Model
- ISA ADN2
- Kategória
- Štúdio › Audio rozhrania
Audio performance
- 0 dBFS reference level
- 22dBu
- Frequency response
- 20Hz - 20kHz ±0.1dB
- THD+N
- -105dB (0.0006%) unweighted, 20Hz - 20kHz; -1dBFS input
- Noise in presence of signal
- -121dBu 'A'-weighted (typical)
- Dynamic range
- 121dB 'A'-weighted (typical), 20Hz - 20kHz
Digital performance
- Supported sample rates
- 44.1 / 48 / 88.2 / 96 / 176.4 / 192 kHz (-4% / -0.1% / +0.1% / +4.167%) at 24 bit
- Clock sources
- Internal or Word Clock
Dante output
- Channel count
- 2 x Dante channels
- Connectors
- 2 x Ethernet standard RJ45 (compatible with Cat 5e and above)
AES3 output
- Channel count
- 2 x Dante channels
- Connector
- 1 x Male XLR
ADAT output
- Channel count
- 2 x ADAT channels
- Connector
- 1 x TOSLINK
- Channel assignments @ 44.1kHz, 48kHz
- Port 1 = Channels 1 - 2
- Channel assignments @ 88.2kHz, 96kHz
- SMUX II... see note: SMUXI Port 1 = Channels 1 - 2
- Channel assignments @ 176.4kHz, 192kHz
- SMUXII Port 1 = Channels 1 - 2
S/PDIF output
- Channel count
- 2 x S/PDIF channels
- Connector
- 1 x RCA phono socket
Word clock
- Word Clock input
- 1 x BNC 75Ω port (switchable termination)
- Word Clock output
- 1 x BNC 75Ω port
Software
- Included software
- RedNet Control, Dante Controller